







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Duarte, CA: What It Costs and What the Job Involves
An iron fence in Duarte typically runs $3,500 to $9,000 installed, and most residential jobs are finished in two to four days. That covers wrought-iron or tubular steel fence, posts set in concrete, and a finish coat. The number that matters is whether you’re working with flat valley-floor soil in 91010 or a sloped 91008 parcel at the base of the San Gabriels, because that single fact can swing the price by a couple thousand dollars. Call (888) 271-7872 for a free on-site estimate.
How the job runs, start to finish

We don’t wing this. Iron fence work follows a fixed sequence, and knowing it in advance is how you avoid a crew that pulls up, eyeballs the property, and improvises.
Stage 1: Site walk and layout (day 1, 1-2 hours)
We mark the exact fence line against your property line, note grade changes, and check for buried utilities and irrigation. On Duarte hillside lots this is where slope becomes real: a straight run across a 15% grade needs stepped panels or raked rails, and you decide which look you want before anything gets dug. You also confirm gate placement now, not later.
Stage 2: Old fence removal and post layout (day 1-2, half a day to a full day)
If there’s a legacy wood or chain fence, it comes out, posts and all. This is also when we spot the things that dog older Duarte properties: frost-heaved or root-lifted footings, and driveway aprons or sidewalk strips that don’t match the plat. We lay out post holes on 6-foot to 8-foot centers depending on panel weight and wind load. You decide post spacing only when we’ve shown you how it changes the look of the run.
Stage 3: Digging and concrete setting (day 2, 4-6 hours)
Posts go into holes typically 24 to 36 inches deep, wider on the uphill side of a slope, and get set in concrete. This is the step that decides whether your fence is plumb in five years. On the hot, dry Duarte summers, the mix needs the right water ratio and cure time or the footings go brittle. Concrete cures overnight minimum before framing begins.
Stage 4: Rails, panels and gates (day 3, 4-6 hours)
Panels go up, rails get welded or bolted depending on the system, and hinges and latches get installed on the gate. On a hillside lot, this is where raked panels earn their keep. You walk the run with us here and flag anything that needs a tweak before finish.
Stage 5: Finish coat and final walkthrough (day 3-4, 2-3 hours)
Powder-coat touch-up or a field-applied finish goes on. We do a final pass on gates, latches and alignment, and hand you the warranty in writing. Total for a typical 60- to 100-foot residential run: two to four days. Bigger estate parcels in 91008 can stretch to five.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll pick between
Iron fence is not one product. These are the real choices in front of you, and the trade-off that comes with each.
- Wrought iron (solid bar stock): The traditional look, heavy, welded joints. It’s the priciest per linear foot but lasts essentially forever with repainting every 8 to 12 years. Suits an estate parcel and anyone who wants it to outlive them.
- Tubular steel (ornamental iron-look): Lighter, often powder-coated, closer to $40-$60 per linear foot installed. Most of the residential market lands here, and it’s a good match for mid-century ranch properties.
- Powder coat vs. field-applied paint: Powder coat is factory-baked and holds up to Duarte’s sun and wind far better. Field paint lets you match an existing gate or color exactly but needs recoating sooner.
- Panel style and picket spacing: Standard, spear-top, or flat-top. Gaps of 4 inches or less keep small pets in; larger gaps read more open. Decide this before posts are set.
- Gate hardware: Self-closing hinges, magnetic latches, and code-compliant pool barriers if you have a pool. This is where people overspend or underspend without realizing it.
What an Iron Fence costs in Duarte, CA

Plan on $3,500 to $9,000 for a residential iron fence in Duarte. A standard 60-foot run of tubular steel with one gate lands near the bottom of that. An estate-length wrought-iron run with multiple gates and slope work pushes toward the top.
The variables that move the number:
- Linear footage: The biggest lever. Most jobs sit between $45 and $95 per linear foot installed depending on material.
- Grade and slope: Stepped or raked panels and deeper footings on hillside runs add labor and concrete.
- Material grade: Tubular steel vs. solid wrought iron can nearly double the material cost on the same length.
- Gates: Each gate adds hardware and labor. Double gates and automated openers cost more.
- Existing removal and site access: Tearing out a legacy fence and getting material up a steep 91008 driveway adds cost.
A written estimate from us breaks out material, labor, gate count, and finish separately. It typically covers demo, footings, panels, hardware and finish. It usually does not cover unexpected utility relocation, retaining wall work behind the fence, or landscape repair around post holes. That’s how you know you’re comparing real numbers.
See the difference
Before
After
Before
After
Before
AfterWhat Duarte homes specifically do to this job
Duarte isn’t flat. It sits where the Angeles National Forest meets the foothills, and that geography changes iron fence work in ways a flatland contractor won’t always plan for. On the 91008 hillside parcels, fence lines run across slope, so posts sit at different depths and panels need raking. Winter rain off the burned San Gabriels means the ground behind a fence line can shift, and a fence that’s fine in March can lean by the following spring if the footings aren’t set deep enough.
The housing stock matters too. The valley floor in 91010 is full of 1950s-60s tract ranchers where the original wood or chain fence is often at end of life; swapping that for iron is a straightforward retrofit, and we see it constantly near City of Hope multifamily edges. Up in the 91008 foothills, custom homes and estate parcels want a fence that reads as permanent, and there the wildland-urban interface rules come into play: noncombustible materials and ember-resistant detailing around the fence line, which iron suits naturally. Many of those jobs are also paired with hillside drainage and retaining work, and homeowners often pair this with Patios, Walkways & Pool Decks in Duarte when the yard is getting an overhaul at the same time. If the fence is part of a full Fence Installation in Duarte project, we scope it all in one pass. And if you’re also adding square footage, homeowners often pair this with ADU Design & Permitting in Duarte. We cover all of it through our Fence Installation service, and if you’re checking whether we work your street, start at our Duarte service-area page.
Serving Duarte, CA – Our Local Coverage Area
We serve Duarte and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Iron Fence in Duarte

Most Duarte iron fence jobs finish in two to four days. A standard residential run of 60 to 100 feet is on the shorter end; hillside runs, larger estate parcels, and multi-gate jobs stretch toward the top. Call (888) 271-7872 for a timeline for your property.
In most residential cases a fence at or under the standard height limit doesn’t need a building permit, but height limits and setbacks vary by lot and zone, and hillside parcels up in 91008 can carry extra review. We confirm your specific requirements before digging. Call (888) 271-7872 to talk through your lot.
Yes, in most cases. We locate utilities before digging and route posts to avoid irrigation lines and plumbing runs. Existing mature landscaping near the fence line is where it gets tight, and we’ll tell you upfront if a plant needs to move. Call (888) 271-7872 for an on-site look.
Expect $3,500 to $9,000 for a residential iron fence in Duarte. Material grade, total footage, slope, and gate count are what move the number, and a written estimate breaks each one out. Call (888) 271-7872 for an exact quote; estimates are free.
Every iron fence we install is covered by our 730-Day Done Right Promise: if it isn’t done right, we make it right. That’s one of the longest workmanship guarantees in residential construction, and you get it in writing. Call (888) 271-7872 to schedule an estimate.
Get a free estimate for your iron fence in Duarte
We’ll come to your property, walk the line, check the grade and utilities, and hand you a written estimate that breaks out material, labor, and gates. No surprises after the first dig. Call (888) 271-7872 to schedule your free estimate – a live person answers around the clock, and the number you see is the number you pay.
Written by the team at Groundwork Construction Co.












