







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in South San Jose Hills, CA: What It Costs and How Long It Takes
A tub-to-shower conversion in South San Jose Hills typically runs $4,130 to $11,800 and takes three to five working days once materials are on site. The job means pulling the old tub and its surround, reworking the drain and valve to shower height, waterproofing the wet area, setting a new base or mud pan, tiling the walls, and hanging glass. Call (888) 271-7872 and we’ll walk your stall, check the drain and valve, and hand you a written line-item number before anything gets demoed.
How a Tub-to-Shower Conversion Actually Runs, Stage by Stage

Every conversion follows the same order. Skipping a stage is how you end up with a shower that leaks into the ceiling below.
Day 1 – Demo and first look at what’s behind the wall
We shut the water, cut out the tub, and haul out the surround, drywall, and old valve trim. Everything gets floor protection and a tarp corridor before we swing a hammer. This is the day the unknowns show up: a rusted galvanized stub-out, a slow drain, dry rot behind the tub apron. We photograph each one and price any change with you in writing before we continue, no after-the-fact surprises.
Day 1 to 2 – Rough plumbing and framing
The drain gets relocated from tub height to shower height, the pressure valve and mixing valve get swapped, and any needed blocking or framing goes in. If you’re moving the drain line more than a few feet or shifting fixtures to a new wall, the first sign of real cost shows up here. This is also when the permit inspection for rough plumbing is scheduled.
Day 2 to 3 – Waterproofing, the stage that decides the job
We build a sloped mud pan (or set a manufacturer base), tape and mortar the seams, and roll on a bonded waterproof membrane across the walls and floor to a minimum thickness. A flood test runs overnight where the scope calls for it. This step costs a few hundred dollars and is the single best insurance against a shower that fails five years in. Don’t skip it for a cheaper quote.
Day 3 to 5 – Tile, fixtures, glass
Walls get set, grouted, and sealed. Fixture trim, valve handle, showerhead, and any niche or bench go in. Frameless or framed glass is templated once the tile is final, so it usually installs on the last day or a day after. Your choices to keep moving here are tile and glass style; if you’re unsure, we bring samples.
Final walkthrough
We test the drain, check for any weep, verify the valve functions hot to cold, clean grout haze, and walk you through care. The work is covered by our 730-Day Done Right Promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between, and What Each One Really Costs You
Almost every tub-to-shower decision falls into a handful of real choices. Here’s the honest trade on each.
- Acrylic or fiberglass base and wall kit. The budget end, real installed cost usually $4,130 to $6,500. Fast and sealed, but the walls can flex and it won’t hold up to decades of use like tile. Best if the shower will be a rental or a guest bath.
- Tiled shower with a pre-made pan. Roughly $6,000 to $8,500. Durable walls and a factory-sloped base means fewer failure points. Solid middle choice for a family bathroom.
- Fully tiled shower with a custom mud pan. $8,000 to $11,800. This is the one that lasts. More labor for the slope and waterproofing, and you get to pick any tile size, tile pattern, niche and bench.
- Glass. Frameless glass costs noticeably more than a framed door but reads cleaner and is easier to keep looking sharp. A framed slider is the value move for a shower under 5 feet wide.
- Valve and fixture grade. A basic pressure-balance valve is included in the base scope. Thermostatic or digital valves, and designer trim, push the number up. Worth it if you have young kids or hot-water control concerns.
What a Tub-to-Shower Conversion Costs in South San Jose Hills, CA

Plan on $4,130 to $11,800 for a tub-to-shower conversion in South San Jose Hills, all in, with permits and glass included in the high end. The final number depends on five things, in order of how much they move it:
- Size. Converting a standard 5-foot tub alcove is the low end. A 60-inch walk-in or a shower that extends into what was closet or wall space costs more in framing and tile.
- Existing condition. Original galvanized plumbing, a soft subfloor, or dry rot behind the tub apron adds repair cost you can’t price until the wall is open. On South San Jose Hills homes with galvanized supply lines still in place, this is common.
- Moving plumbing or structure. Keeping the drain and valve where they are is the cheapest route. Shifting to a new wall or a different drain location adds rough plumbing, framing, and inspection scope.
- Material grade. Acrylic kit at one end, fully tiled with a custom pan and frameless glass at the other. That spread alone is most of the gap between the low and high end.
- Permit scope. A like-for-like swap is a lighter permit than one that relocates plumbing or alters framing.
Every written estimate we hand you itemizes demo, rough plumbing, waterproofing, tile material, glass, fixtures, permit, and disposal. What it can’t include is what’s hidden behind the wall until we look; anything we find is priced in writing and approved by you before work continues. Upfront pricing, no surprises. Financing at 0% for 18 months is available if you’d rather spread it out.
See the difference
Before
After
Before
After
Before
AfterWhat South San Jose Hills Homes Specifically Do to This Job
South San Jose Hills (ZIP 91792) isn’t a typical subdivision job, and it changes the scope in ways a flat-lot city page can’t mention. This is one of the last unincorporated pockets of LA County where lots of half an acre to two-plus acres, many still zoned for horses, sit on sloped terrain with long private driveways and older residential infrastructure. That matters most for what we find under the tub: many homes in the 1960s-1980s ranch and custom mix still carry galvanized supply lines and original electrical, and hillside parcels bring site-specific conditions that push plumbing access into a crawlspace or a slab cut that lives on a slope. Before a single tile goes in, we confirm the drain line still has fall to the sewer and that any required restraint or blocking is right for the framing. Permits here run through LA County, not a city hall, and that affects the inspection sequence. If you’re converting a bath as part of a larger project, this often ties to Bathroom Remodeling in South San Jose Hills and, on the exterior side of the same house, homeowners often pair this with Metal Roofing in South San Jose Hills when they’re upgrading the whole envelope.
Common Scenarios We See in South San Jose Hills
Here’s what tends to come up once the demo starts on a conversion in the area.
- The 1970s alcove with a cast iron drain. The pipe is often still sound, but the trap and stub need a cleanout and a fernco coupling. Budget for a few hundred extra if the drain looks suspicious on day 1.
- Galvanized supply lines. Very common in the older custom and ranch homes on the sloped parcels. If the shutoff at the wall is crumbly, we replace the stub and shutoff as part of rough plumbing rather than risk a break later.
- Slab on grade with no crawl access. Move-the-drain decisions get made carefully here; staying in the existing footprint is the cleanest way to keep the permit light.
- Aging waterproofing on a prior remodel. If the old surround was set over greenboard, we strip it and rebuild with a bonded membrane. Cheap prior work is the most common hidden cost.
Serving South San Jose Hills, CA – Our Local Coverage Area
We serve South San Jose Hills and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Tub-to-Shower Conversion in South San Jose Hills
Most conversions take three to five working days on site, with an extra day or two if glass has to be templated after tile. Demo is one day, rough plumbing and waterproofing two, tile and glass the rest. Call (888) 271-7872 for a schedule tied to your specific bath.
Yes, a permit is generally required once you’re changing plumbing or altering the wet area, and South San Jose Hills permits run through LA County because the area is unincorporated. We pull the permit under the company name and handle the inspection. If you’re unsure whether your swap triggers one, call and we’ll tell you straight.
Often, yes. If the new shower stays in the same alcove footprint, the drain can usually stay put and only the valve gets raised to shower height. That keeps the job at the lower end of the $4,130 to $11,800 range. Call (888) 271-7872 and we’ll measure your stall and confirm.
No, not without your written approval. Our estimate itemizes every line, and if demo turns up hidden damage (dry rot, a failing drain, galvanized stubs), we price the fix and you approve it before we continue. Upfront pricing, no surprises, is the whole point.
Every tub-to-shower conversion we complete is covered by our 730-Day Done Right Promise. That’s the company guarantee; product warranties from the tile and fixture manufacturers also apply and we pass those to you. Call (888) 271-7872 for a free on-site estimate.
Get a Free Tub-to-Shower Conversion Estimate in South San Jose Hills
We’ll come out, measure the alcove, look at the drain and valve, and leave you with a written line-item quote and a realistic start date. If your project is bigger than one bath, we’ll scope it as our Bathroom Remodeling service or break it into stages. We cover South San Jose Hills and the surrounding area, including Valinda, West Covina, La Puente and Hacienda Heights. Call (888) 271-7872 today for your free estimate.












