







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Aluminum Fence Installation in Whittier, CA: What It Costs and How Long It Takes
An aluminum fence in Whittier typically runs $4,000 – $10,000 installed, and most residential jobs finish in two to four working days once the fence line is marked and utility locates clear. That range covers powder-coated panels, posts set in concrete footings, and gates hung on adjustable hinges. The variables that push a job toward the top end are slope, fence height, ornamental picket style, and whether you’re matching a design guideline near the historic core. Call (888) 271-7872 for a free on-site estimate with a written line-item quote.
How an Aluminum Fence Job Actually Runs, Start to Finish

Aluminum fencing looks simple from the street, and that’s the trap. Most of the work happens before a single panel goes up. Here’s the real sequence we follow in Whittier.
Stage 1: Site visit and layout (about 1 hour)
We walk the actual fence line with you, not just eyeball it from the curb. That means deciding corners, gate locations, and whether the fence runs behind the detached garage or stops at its corner. You’ll decide style and height at this stage, because both affect footing depth and post spacing. On Whittier properties with narrow side yards, we also check that a wheelbarrow and a post hole digger can physically reach the back line.
Stage 2: Utility locate and call-in (2 – 3 business days of waiting)
Before we dig anywhere near a fence line, we call in the 811 utility locate. This is the step sloppy crews skip and then discover a gas or irrigation line with a shovel. In older Whittier lots, it’s not unusual to find outbuildings’ water and electrical lines running toward a back fence. You don’t have to do anything here beyond leaving a few feet of access.
Stage 3: Removal and prep (4 – 8 hours for a typical residential run)
If there’s an old fence in the way, you decide whether it comes out fully or whether we leave the existing posts and retrofit. Green or composite wood posts that are still solid at grade can sometimes be skipped, but most of the time the old line goes. We mark the new line, clear turf, and dig footings to frost-safe depth. You’ll decide at this stage whether to keep the old fence material or have us haul it off, which affects disposal cost.
Stage 4: Posts, panels, and gates (1 – 2 days)
Posts get set in concrete and need to cure before the panels hang. On a 100-foot run, that means one day pouring posts and a following day setting panels and gates. Gates take the longest because the hinge and latch alignment has to be dead square or it will sag within a season. This is the day a minor line adjustment is cheapest to make, so speak up if a panel sits closer to a planter than you pictured.
Stage 5: Final walk and punch list (about 30 minutes)
We walk the whole line with you, check gate swing, confirm post spacing, and photograph the finished fence for our records. If a cap or bracket is wrong, it’s on the list before we leave. That’s the spirit behind our 730-Day Done Right Promise: if something isn’t right down the line, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Real Options You’ll Choose Between on an Aluminum Fence
Aluminum isn’t one product. What you pick changes both the cost and how the fence behaves in San Gabriel Valley sun.
- Powder-coated aluminum vs. raw or painted finish. Powder coat holds its color through Whittier’s hot, dry summers far better than paint and resists the chalking you see on cheaper finishes. The trade-off is a moderate upcharge for a lighter, more durable finish. If you’re planning to repaint every few years, a painted finish is cheaper upfront.
- Flat-top vs. ornamental/top-and-bottom picket style. Flat-top panels are the workhorse for pool and yard enclosures and cost less per linear foot. Ornamental styles with rings or scrollwork suit a Craftsman or period-revival home near Uptown, but they add to the per-foot price and a longer lead on special-order panels.
- Height: 4 ft, 5 ft, or 6 ft. Each step up in height increases material, load, and footing requirements.
- Gate type: single walk gate vs. double drive gate. A single walk gate is the common pick; a double drive gate adds a much larger install cost and needs wider posts and heavier hardware.
- Post caps and finials. A small line item, but it’s what most people notice when they pull into the driveway.
Where prefab systems make sense (a clean, code-compliant panel system with manufacturer engineering), we’ll point you toward them. Where they don’t, we’ll say so, and I’d rather tell you that than sell you a product that fights your yard. If your project also includes a wider set of fencing needs, we cover the whole scope through our Fence Installation service.
What an Aluminum Fence Costs in Whittier, CA

Residential aluminum fence installation in Whittier runs $4,000 – $10,000 for a typical yard. That’s the honest bracket, not a teaser rate. What pushes a job toward one end or the other comes down to five variables.
- Linear footage. This is the biggest driver. A 60-foot run sits near the bottom of the range; 150 feet pushes toward the top.
- Height and style. Six-foot ornamental panels cost meaningfully more per foot than a four-foot flat-top system.
- Slope and grade. Whittier yards often have some fall. Panels need to step down the slope, which means more posts and more labor.
- Removal and disposal of an existing fence. Tear-out and hauling is a real line item, often hundreds of dollars.
- Gates and custom cuts. Each gate and each return corner adds to the count of posts and hardware.
What’s included in a written estimate: panels, posts, concrete, gate hardware, standard post caps, and labor. What’s often not: custom fabrication, historic-district design review fees where they apply, and old-fence disposal unless you ask for it upfront. We put all of it in writing so the number you see is the number you pay. Homeowners planning external work often pair an aluminum fence with Driveway Repair & Replacement in Whittier while the equipment is already on site.
See the difference
Before
After
Before
After
Before
AfterWhat Whittier Homes Specifically Do to This Aluminum Fence Job
The fence line in Whittier tells you which part of town you’re standing in. In Uptown Whittier and along the Greenleaf and Philadelphia corridors, the 1900s – 1930s Craftsman and period-revival homes often have compact lots with detached garages, and any exterior change can run through the city’s historic resources review. That means an aluminum fence that’s routine in the postwar tracts of 90603 or 90605 may need design review before it goes up near the historic core, so we plan for that review at the front end rather than after posts are poured. Out east and south, the 1950s – 60s tract homes have their own signature problems: non-conforming lot lines, shallow-footing old fences, and irrigation lines that cross where you’d never guess. Whittier’s hot, dry summers also mean sun exposure that eats cheap finishes, which is why we push powder-coated systems on this job. If your scope grows beyond a single line into a Fence Installation in Whittier, that’s a different conversation and a different page. We cover the alley-to-alley work throughout the 90609, 90610, 90605, and 90603 ZIPs, so check our Whittier service page for the surrounding line.
Serving Whittier, CA – Our Local Coverage Area
We serve Whittier and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked, Aluminum Fence in Whittier

A typical residential aluminum fence takes two to four working days on site, once utility locates clear. The build itself is fast; the locate wait and any concrete cure can stretch the calendar by a week or so. Call (888) 271-7872 and we’ll put a real duration on your specific line.
Most residential aluminum fences in Whittier fall under the city’s height limits and don’t need a full building permit, but anything near the historic core or above the standard height can trigger design review. We handle the paperwork and call it out in the estimate. Call (888) 271-7872 to confirm what applies to your address.
Yes, we can set aluminum posts into an existing hardscape, but the post spacing and base detail need to be planned carefully to avoid cracking the slab. If your patio or walkway needs work, homeowners often pair this with Patios, Walkways & Pool Decks in Whittier, and we’ll coordinate the two so the fence posts go in cleanly. Estimates are free.
Aluminum outlasts wood here by a wide margin because it doesn’t rot, warp, or need repainting every few years in the heat. The upfront cost sits higher than a basic wood fence; the long-run cost is lower. Call (888) 271-7872 for a side-by-side quote.
All our fence work is covered by the 730-Day Done Right Promise, our workmanship guarantee that’s on the longer end of what’s offered in this space. The manufacturer’s warranty on panels and coatings is separate and depends on the system you choose. We’ll spell out both in your written estimate.
Get a Free, No-Pressure Aluminum Fence Estimate in Whittier
Call (888) 271-7872 and a real person picks up, day or night, to schedule your free on-site estimate. We’ll walk the line, measure, note slope and access, and send a written line-item quote. No surprise charges, and financing is available at 0% for 18 months, plus $1,000 off projects over $10,000. If it’s not done right, we make it right.
Written by the team at Groundwork Construction Co.












