







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Whittier, CA: What It Costs and How Long It Takes
Metal roofing in Whittier typically runs $15,000 to $40,000 for a full residential roof, and most jobs take two to four weeks from tear-off to final inspection. The number swings on square footage, panel type, and how much of the original roof deck and framing has to be repaired before new metal goes down. Call (888) 271-7872 and we’ll walk your roof, measure it, and put the range in writing before any work is scheduled.
How a Metal Roof Goes On, Stage by Stage
Metal isn’t a one-day job, and anyone who tells you otherwise is skipping steps that matter in Whittier’s heat and wind. Here’s the real sequence.
- Day 1: Teardown and deck inspection. We strip the old shingles or tile and expose the sheathing. On older Whittier homes this is where we find soft decking, dry-rotted fascia, or the occasional layer of original cedar shakes that has to come off too. You decide then whether to replace full sheets of decking or patch. Most full tear-offs take a day; larger or multi-layer roofs take two.
- Days 2 – 3: Structural and underlayment work. Any framing repairs get done, then a high-temp synthetic underlayment goes down over the whole deck, followed by drip edge and eave flashing. On Whittier roofs with a low slope over a porch or addition, we add a peel-and-stick membrane in those sections. This stage is where the roof actually becomes watertight, and it’s the stage most homeowners never see because it happens before the metal arrives.
- Days 4 – 10: Panel installation. Panels get cut, laid out, and fastened in sequence, with ridge caps and trim closed as we go. A typical single-family roof in the 90601 or 90604 ZIP codes takes five to seven working days for the panel field. Standing seam goes on faster per square than exposed-fastener panels because there are no screws to drive through the face.
- Days 11 – 13: Flashing, penetrations, and valleys. Vents, chimney surrounds, skylight curbs, and valley intersections are the leak points, so they get their own careful pass. This is a decision point for you: whether to replace old attic vents with new ridge venting while the roof is open, which we recommend doing now rather than later.
- Final stage: Inspection and cleanup. We coordinate the city inspection (more on permits below), do a magnet sweep for fasteners, and walk the roof with you. Most Whittier jobs wrap in two to four weeks, with weather days and Santa Ana wind events the main thing that can push the schedule.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Panel Types, Finishes, and the Trade-Offs You’re Choosing Between
Metal roofing isn’t one product. What you pick here drives both the price and how the roof performs over the next forty years.
- Standing seam panels: the concealed-fastener option, with raised seams that lock together. It sheds debris and wind-driven rain well, which matters on Whittier’s exposed ridges during Santa Ana events. It costs the most per square and needs a crew that knows the folding and seaming, but it has the fewest failure points because nothing pierces the panel face.
- Exposed-fastener panels (screw-down): the more economical choice, popular on detached garages and outbuildings. The trade-off is the washers on those screws: they age faster in UV and heat, so expect to check and re-seal them periodically.
- Stone-coated steel: metal with a granular coating that mimics tile or shake. It’s a real fit for Whittier’s period-revival homes where a shiny metal roof would look out of place and full tile would overload the framing. It costs more than bare panels but less than standing seam, and it adds weight that must be checked against the existing structure.
- Finish and color: factory-baked paint systems hold color far better than field-painted metal. Choosing a lighter color is worth considering in the eastern LA Basin heat because it cuts attic heat gain – and on a Whittier home with a hot, unshaded south-facing slope, that difference shows up on your summer bill.
- Panel gauge and substrate: thicker steel panels resist hail and foot traffic better. Honest trade-off: heavier panels cost more and, on a 1950s tract home, may need a framing check before you commit.
What Metal Roofing Costs in Whittier, CA

Expect $15,000 to $40,000 for a full metal roof on a typical Whittier single-family home. That’s the honest range, and here’s what pushes a job toward the low or high end:
- Roof size and complexity: a simple gable runs cheaper than a cut-up roof with multiple valleys, dormers, and hips, which eats labor and material waste.
- Condition of the deck and framing: soft sheathing, dry rot at the eaves, or a re-nail required by the inspector all add cost. On a 1920s Whittier home, surprises under the old roof are the single biggest swing factor.
- Panel type and gauge: screw-down panels sit at the bottom of the range; stone-coated steel and standing seam climb toward the top.
- Permit scope: a straightforward re-roof permit is different from a permit that includes structural repair or a change of roofing material classification, which the city may review more carefully.
- Access: a narrow lot with a detached garage and a tight side yard slows material handling and adds a day or two of labor.
Your written estimate itemizes tear-off, decking repair allowance, underlayment, panels, trim, flashing, and permit fees, so the number you see is the number you pay. It typically does not include structural framing repair discovered mid-job, gutter replacement, or painting of fascia – all of which we price separately before touching them.
See the difference
Before
After
Before
After
Before
AfterWhat Whittier’s Older Housing Stock Does to a Metal Roof Job
Whittier is a built-out, older first-ring suburb where almost all roofing work is a rebuild on an aging home, not new construction – and that changes the job. Much of the roof work we do sits on 1900s – 1930s Craftsmans and period-revival homes around Uptown Whittier and the flats near Greenleaf and Philadelphia, where you’re dealing with decades of layered shingles, older sheathing, and sometimes framing that predates modern codes. If your home falls within the historic-district review area, a change in roof material or color can trigger design review, so planning that early is not optional. The postwar tract homes in ZIP codes 90604 and the surrounding east-side neighborhoods are more straightforward, but the original venting and eave details still need correcting before panels go on. The climate shapes the schedule too: hot, dry summers and Santa Ana wind events make wind uplift detailing and heat-rated underlayment a real consideration, and winter rains mean we plan tear-off so the roof is never open to weather overnight. The failure modes we see most are nail fatigue on original shake roofs, wind-scoured tile and shingle edges on exposed slopes, and rusted-through gutters hanging off old fascia.
Serving Whittier, CA – Our Local Coverage Area
We serve Whittier and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Whittier

Two to four weeks for a typical single-family home, from tear-off through final inspection. Panel installation itself is five to seven working days; the rest is prep, flashing, and inspection. Call (888) 271-7872 for a schedule estimate on your specific roof.
Yes. A re-roof requires a permit, and if your home sits in or near the Uptown historic-district review area, a change of material or color may also need design review approval. We pull the permits and coordinate the inspections as part of the job.
Usually, yes – metal is lighter than tile and comparable to asphalt, so most Whittier frames handle it without modification. Any home getting a heavier stone-coated steel product should have the framing checked first, and we confirm that during the walk-through.
The range is $15,000 to $40,000, with the exact figure set by size, panel type, deck condition, and permit scope. The line-item estimate is fixed for the scope we quote; if we open the roof and find hidden framing damage, we stop, show you, and price the repair before proceeding. Call (888) 271-7872 for an exact quote – estimates are free.
Panels carry the manufacturer’s finish warranty, and our workmanship is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in residential construction, and it’s in writing.
Get a Free Metal Roofing Estimate in Whittier
Call (888) 271-7872 to schedule a free on-site estimate. A live person answers, around the clock, and we’ll set a time to measure your roof, inspect the deck, and hand you a written line-item quote – plus options for financing and the $1,000 off projects over $10,000. If your project overlaps with a wider scope of work, it’s part of a full Roofing in Whittier plan we’re glad to price alongside it. You can also explore our Roofing service for the broader picture, and we also serve homeowners throughout Whittier – many of whom pair their new roof with Window Replacement in Whittier or Impact Windows & Doors in Whittier while we’re already on the property. No pressure, no voicemail black holes.
Written by the team at Groundwork Construction Co.












