







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Hacienda Heights: What It Costs and How Long It Takes
A full metal roof on a Hacienda Heights home typically runs $15,000 to $40,000 and takes three to six days on the roof once the order lands, depending on roof pitch, square footage, and whether the panels are exposed fastener or standing seam. That number covers tear-off of the old roof, new underlayment, panels, trim, and flashing. Older homes on the hillside often add fascia repair before panels go up. Call (888) 271-7872 for a free on-site estimate on your specific roofline.
How a Metal Roof Goes On: Stage by Stage

Metal roofing isn’t a single visit. Here’s the real sequence we run, and what you as the homeowner decide at each step.
Day 1: Inspection and layout
We walk the roof, measure every plane, check the sheathing under the shingles, and look at the fascia and rafters. On a 1960s ranch in Hacienda Heights, that inspection often turns up soft decking or fascia rot from years of sun damage. You’ll decide here whether to replace sheathing at $60 – $120 per sheet or patch what’s solid. This stage takes two to three hours.
Day 1 – 2: Tear-off and decking prep
Crews strip the old shingles, inspect the sheathing, and repair what the inspection flagged. For a 2,000-square-foot roof, tear-off runs four to six hours. We dump the old material and prep the deck for underlayment the same day when weather allows. You’ll want a dumpster staged on the driveway, which on a steep Hacienda Heights slope often means coordinating with the neighbors about street access.
Day 2: Underlayment and flashing
Synthetic underlayment goes down first, followed by drip edge, valley flashing, and pipe boots. This is the layer that actually keeps water out, and it’s where cut corners show up years later. Expect half a day for a typical ranch roof. No decision required from you here unless the inspection found a chimney or skylight that needs reflashing.
Day 3 – 5: Panel installation
Panels are cut, hemmed, and screwed down in sequence, starting at the eave and working up. Exposed-fastener panels go faster (two to three days). Standing seam takes three to four days because each seam is crimped or snapped with precise alignment. Length of panel and roof pitch both slow the work. This is where the look of the roof is locked in.
Day 5 – 6: Trim, ridge, and final walkthrough
Ridge caps, gable trim, and closures finish the edges. Then we do the water test, walk the whole roof with you, and hand over the written warranty. Final inspection by LA County happens after this, usually within a week or two of the walkthrough.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Panel type and finish drive both the cost and the look. Here’s how the trade-off plays out.
- Exposed-fastener panels (through-screwed corrugated or ribbed): the budget option, usually $2.50 – $4 per square foot for material. Fasteners sit exposed and need re-sealing every 10 – 15 years, but they hold up in the Puente Hills wind and cost the least.
- Standing seam panels: the premium choice, $5 – $9 per square foot material. Concealed fasteners, cleaner lines, and a lifespan that often outlasts the home. Better choice for hillside view properties where curb appeal matters.
- Stone-coated steel: mimics tile or shake at roughly $4 – $6 per square foot. Popular on Hacienda Heights ranch homes that want the metal durability without the modern look.
- Finish and color: standard Kynar 500 or PVDF finishes add $0.50 – $1.50 per square foot over bare galvanized. Worth it here; the summer sun and Santa Ana winds strip cheaper paints.
- Panel gauge: 26-gauge is the residential standard. 24-gauge runs roughly 15% more in material but resists hail and wind better on exposed hillside lots.
Brand-wise, GAF and CertainTeed both make residential metal systems that pair with their underlayment and flashing components, which simplifies the warranty picture. Owens Corning’s metal options are worth a look too if you want the same brand across the roof and gutters.
What Metal Roofing Costs in Hacienda Heights, CA

Expect $15,000 to $40,000 for the full job on most Hacienda Heights homes. Typical line items:
- Tear-off and disposal: $1,500 – $3,500
- Sheathing repair: $60 – $120 per sheet if needed
- Underlayment and flashing: $1,200 – $2,500
- Panel material and installation: $10,000 – $28,000
- Fascia and trim repair: $800 – $2,500
- Permit and inspection fees: $400 – $900
What pushes a job to the high end: steep hillside pitch that needs scaffolding, more than 30 squares of roof, standing seam over exposed fastener, full fascia replacement, or a second-story section that needs fall protection. What keeps it low: a simple single-story footprint, exposed fastener, no sheathing damage, and shingles that come off clean.
A written estimate from us lists every line. It also names what’s not covered – typically painting the fascia, gutter replacement, and any structural repair that only shows up after tear-off. If the price is going to move, you hear it before we touch the roof.
See the difference
Before
After
Before
After
Before
AfterWhat Hacienda Heights Homes Specifically Do to This Job
Hacienda Heights is unincorporated, so metal roofing permits and inspections run through LA County rather than a city building department. That’s a real difference. County inspectors look hard at ice-and-water barrier on valleys, panel attachment specs in high-wind zones, and whether the sheathing meets the current nailing schedule. Getting this wrong means a re-inspection and a delay, so we pull the permit before day one.
The housing stock keeps it interesting. Most of what we roof in the 91745 ZIP is single-story and split-level ranch homes built from the late 1950s through the 1970s. Many still have shallow roof overhangs and original fascia boards that have soaked up forty-plus years of sun and winter rain. On hillside streets above the Puente Hills, that fascia is often the first thing to fail, so we budget for it. Hillside lots also mean steep driveways and retaining walls that make staging the dumpster a genuine planning task. If a roof job rolls into a broader structural repair, that’s a conversation for our Roofing in Hacienda Heights team.
The climate does most of the damage. Intense summer sun bakes the south and west-facing planes, and periodic Santa Ana winds drive grit and heat into every seam. Brush-adjacent properties want Class A fire-rated panels, which most modern metal systems already carry. Winter rains saturate the hillside soil, so proper flashing and drainage matter more than on a flat-lot house.
One more quirk worth naming: many Hacienda Heights homes have original 1960s aluminum wiring running through the attic to light fixtures and fans. If the roof work exposes that wiring, we flag it and recommend an electrician evaluate it before we close up. We’re not the electrician, but we know to look. Homeowners often pair roof work with exterior upgrades; our Window Replacement in Hacienda Heights and Impact Windows & Doors in Hacienda Heights jobs go in smoothly once the roof is finished.
For the full picture of what our Roofing division covers, or to see everything we do across Hacienda Heights, those pages lay it out.
Serving Hacienda Heights, CA – Our Local Coverage Area
We serve Hacienda Heights and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions: Metal Roofing in Hacienda Heights

Most Hacienda Heights metal roofing jobs finish in three to six days on the roof, plus a week or two for permit and inspection. Smaller single-story ranch roofs lean toward the short end. Larger or steeper homes take longer. Call (888) 271-7872 for a realistic date range after we measure.
Yes. Because Hacienda Heights is unincorporated, metal roofing requires an LA County building permit and inspection. We pull the permit and schedule the inspection as part of the job. Homeowners who go without one face problems at resale. Call for a free estimate that includes permit fees.
We don’t recommend it. Panel attachment needs a clean sheathing surface, and skipping tear-off hides rot that shows up years later. We tear off, inspect, and repair. Estimates are free – call (888) 271-7872 to schedule the inspection.
Metal roofing in Hacienda Heights runs $15,000 to $40,000 for most homes. The wide range reflects roof size, pitch, panel type, and whether fascia or sheathing needs repair. Call (888) 271-7872 – estimates are free, and the quote is line-itemed.
Our work is covered by the 730-Day Done Right Promise – one of the longest workmanship guarantees in residential construction – on top of the manufacturer’s panel warranty, which usually runs 30 to 50 years depending on the system. Call (888) 271-7872 for the specifics on your chosen panel.
Get a Free Metal Roofing Estimate in Hacienda Heights
Call (888) 271-7872 and a live person answers any hour. We’ll set a free on-site estimate, measure the roof, inspect the fascia and sheathing, and hand you a written line-item quote for metal roofing in Hacienda Heights with a fixed price and permit fees spelled out. No change orders mid-job. Our technicians bring up to 12 years of experience, arrive in uniform, and back the work with the 730-Day Done Right Promise.
Written by the team at Groundwork Construction Co.












